Changing the time on a Amanda@SOHO system can be done from any extension but you must log in as the administrator.

1. Dial the voice mail pilot extension number (the same number normally used to check voice mail)
2. When the voice mail system answers press "STAR"
3. Enter "999#" then enter the administration password (default = 999) and press "#"
4. Enter "883"
5. Enter the date (MMDDYY) then press "#"
6. Enter the time (HHMM) then press "#"
7. The system will prompt for AM or PM
8. Exit

Top of Page

Changing the time on a Partner system must be done from extension # 10.

1. At station/ext. # 10, press feature, 0, 0
2. Press the left intercom 2 times
3. Enter # 103
4. Enter the correct time in 24 hr. format, for example:
   • to set the time for 09:00 A.M., enter 0900
   • to set the time for 04:45 P.M., enter 1645
5. Press feature, 0, 0

Top of Page

Changing the time on an Iwatsu ADIX system can be done from the operator DSS console or from the attendant console.

1. Press "ICM" + "FEAT" + "6" + "4"
2. Enter the time "HH MM" using the 24 hour military clock
3. Press "SPKR"

1. Press "ETC" + "ETC" + "ETC" + "F1"
2. Enter the time "HH MM" using the 24 hour military clock
3. Press "RLS"

Top of Page

Changing the time on a Atlas 32, 64 or 128 system can be done from any display phone.

1. Enter programming mode by pressing "PROG - PROG - 1 - 2 - 3 - HOLD"
2. Enter mode 09
3. Enter date "YYMMDD"
4. Enter time "HHMM" (in 24 Hour format)
5. Enter day of week 0 - 6 (4 for Thursday)
6. Press "HOLD" at any stage to save a change

Top of Page

Changing the time on a Electra Elite & Professional system must be done from the "main" or primary phone. It is usually extension # 100.

1. Press "FEATURE"
2. Dial "9#"
3. Enter hour and minute
4. Press "RECALL" to change AM/PM setting
5. Press "HOLD" to change the calendar setting
6. Press "RECALL" to change the day of week
7. Dial "#" to move the cursor to day of month field
8. Enter day of month
9. Press "RECALL" to select month
10. Dial "#"to move the cursor to year field
11. Enter last 2 digits of year
12. Press "FEATURE"

Top of Page

Changing the time on a Norstar system must be done using a display phone. Using a M7310 or T7316 the right 2 buttons under the display are "NEXT" and "SHOW" respectively.

1. To enter programming mode press "FEATURE" and "* * 2 6 6 3 4 4"
2. Enter password (default = 266344) - display should read "Terminals & Sets"
3. Press "NEXT" 5 times - display should read "Time and Date"
4. Press "SHOW" - display should read "Hour:___"
5. Press softkey "CHANGE"
6. Enter hour - display should read "AM OK or Change"
7. Select AM or PM
8. Press "NEXT" - display should read "Minutes:___"
9. Press softkey "CHANGE"
10. Enter minutes
11. Press "NEXT" - display should read "Year:___"
12. Press softkey "CHANGE"
13. Enter year
14. Press "NEXT" - display should read "Month:___"
15. Press softkey "CHANGE"
16. Enter month
17. Press "NEXT" - display should read "Day:___"
18. Press softkey "CHANGE"
19. Enter day
20. Press "NEXT"

Top of Page

Changing the time on a Panasonic KX-TA624 & KX-TA824 system must be done from extension # 101 using a display phone.

1. Press the "PROGRAM" button on the face of the phone
2. Enter programming mode by pressing "STAR" - "POUND" - "1234" (default password = 1234)
3. Enter program # 000
4. Press "SPEAKER" button
5. Press "FORWARD/DND" button to change to the hour selection
6. Press "TRANSFER" button and enter the hour
7. Press "FORWARD/DND" button to change to the minutes parameter
8. Press "TRANSFER" button and enter the minutes
9. Press "FORWARD/DND" button to change to the AM/PM parameter
10. Press "MUTE" button to select AM or PM
11. Press "STORE" button (listen for 1 tone if procedure was executed correctly / 3 tones if procedure failed)
12. Press "HOLD" button
13. Press the "PROGRAM" button on the face of the phone

Top of Page

Changing the time on a Panasonic KX-TVS voice mail system can be done from any phone.

1. Dial the TVS pilot number (extension 107 or 115)
2. When the voice mail system answers press "#" + "6" + "STAR"
3. Log into the message manager's mailbox (999)
4. Press "6" for other features
5. Press "3" to set the time & date
6. Press "1" to change the current time (press "0" for help)
7. Enter the hour then press "#" or enter the hour and minutes then press "#"
8. Press "1" for AM or "2" for PM
9. Press "2" to accept the new time

Top of Page

Changing the time on a Panasonic digital system can be done from any display phone.

1. Enter programming mode by pressing "PAUSE" then "STAR" button twice, followed by 1, 2, 3, 4
2. Enter program # "000"
3. Press "SPEAKER" button
4. Press "FORWARD/DND" button to change to the hour selection
5. Press "TRANSFER" button and enter the hour
6. Press "FORWARD/DND" button to change to the minutes parameter
7. Press "TRANSFER" button and enter the minutes
8. Press "FORWARD/DND" button to change to the AM/PM parameter
9. Press "MUTE" button to select AM or PM
10. Press "STORE" button
11. Press "HOLD" button
12. Lift and replace handset

Top of Page

Changing the time on a Strata DK system must be done from the "main" or primary phone. It is usually extension # 10, or # 200.

1. With the phone on-hook, dial intercom, #, 652 (depending on the system type, the # may or may not apply)
2. Enter the correct time using HH/MM/SS, like 07:24:00
3. Press redial

Top of Page

System Time/Date must be set by the first programmed Attendant via admin programming or using feature code 692.

1. Dial [692] on the dial pad. A confirmation tone will sound.
2. Enter date and time as follows: YYMMDDHHMM
3. YY = Year (00-99)
4. MM = Month (01-12)
5. DD = Day (01-31)
6. HH = Hour (00-23)
7. MM = Minute (00-59)
8. When the correct number of digits are entered, a confirmation tone will sound.
9. Press the ON/OFF button to OFF to update the display.

Top of Page

Changing the time on a Comdial DX-80 system can be done from any display phone.

1. Press Feature # * and enter in your password (Default password ########)
2. Press Show and enter 0803
3. Press Save then Show
4. The option to change the Year will appear - if you do not need to change the year, press Next - if you need to change this value, press Chg, enter in two digits for the year and press Save then Next
5. The option to change the Month will appear - if you do not need to change the month, press Next - if you need to change this value, press Chg, enter in two digits for the month and press Save then Next
6. The option to change the Day will appear - if you do not need to change the date, press Next - if you need to change this value, press Chg, enter in two digits for the date and press Save then Next
7. The option to change the Weekday will appear - if you do not need to change the weekday, press Next - if you need to change this value, press Chg, to select the weekday, and press Next
8. The option to change the Hour will appear - press Chg and enter in two digits for the hour in military format - press Save then Next
9. The option to change the Minutes will appear - press Chg and enter in two digits for the minutes and press Save
10. Press the Hold button to exit programming mode

Top of Page

Changing the time on a Samsung Prostar 816 system can be done from any display phone with the handset on-hook. (Do not lift handset off hook while programming.

1. Enable technician programming mode
   • Press "#" - "PROGRAMMING" is displayed
   • Dial "20" - "MMC ENABLED" or "MMC DISABLED" is displayed
   • Dial the password (default - 1234) - if wrong password is enter "ERROR" is displayed
   • Dial "1" to enter program mode
   • Press "#"
2. Press "#" key - "PROGRAMMING" is displayed
3. Dial "55" - the display shows "YY MM DD W HH MM" and then the current date is displayed
4. Enter the new date
   • YY = Last two digits of the year
   • MM = Month (01 - 12)
   • DD = Day of the month (01 - 31)
   • W = Day of the week (1 -7 day of the week begins on Monday & ends on Sunday)
   • HH = Hour (Use 24 hour clock)
   • MM = Minutes (0-59)
5. Press "#" - new date is saved

Top of Page

Changing the time on a Avaya Merlin Magix system is accomplished from the system programming console. The date is change separately from the time.

1. Press Menu
2. Press System Program
3. Press Exit or Start
4. Press System
5. Press Date
6. Enter the date as mmddyy where mm = month, dd = day, yy = year
7. Press Enter
8. Press Exit or Back
9. Press Home or Exit

1. Press Menu
2. Press System Program
3. Press Exit or Start
4. Press System
5. Press Time
6. Enter the date as hhmm where hh = hours & mm = minutes
7. Press Enter
8. Press Exit or Back
9. Press Home or Exit

Top of Page

Any display phone can be used to change the time on Toshiba CTX 100 system. Do not lift the handset.

1. Press "Hold"
2. Press * # * # 1 * 2 * 3 *
3. Display shows "Password ="
4. Enter 0 0 0 0 (or applicable system programming password)
5. Press "Hold"
6. Display shows "Prog ="
7. Enter 9 0 2
8. Press "Hold"
9. Display shows "Select Param"

1. Press "Intercom" button
2. Enter yymmdd where yy = year, mm = month, dd = day
3. Press "Hold"
4. Press "Hold" (again)
5. List handset and hang up again

1. Press "Line 1" button (should be button directly above intercom button)
2. Enter hhmmss where hh = hours, mm = minutes, ss = seconds (military time)
3. Press "Hold"
4. Press "Hold" (again)
5. List handset and hang up again

Top of Page

Program from Extension 10 or 100. Do not lift the handset.

1. Press "ON/OFF or Intercom" button
2. Press "PROG" button
3. Dial "# #"
4. Push Line 1
5. Dial "# # #"
6. Enter time in 4 digit, 24 hour format
7. Dial "#"
8. Press "ON/OFF" button

Top of Page

Program from Extension 10 or 100. Do not lift the handset.

1. Press ON/OFF or Intercom button
2. Press PROG button
3. Dial * *
4. Dial the Password (9999)?
5. Dial 1001
6. Press Hold
7. Enter time in 4 digit, 24 hour format
8. Press hold
9. Press ON/OFF button

Top of Page

Program from Extension 10 or 100. Do not lift the handset.

1. Press ON/OFF or Intercom button
2. Press Recall button
3. Dial * *
4. Dial # 4
5. Enter time in 4 digit, 24 hour format
6. Press ON/OFF button

Top of Page

Program from Extension 300. Do not lift the handset.

1. Press #
2. Dial 83
3. Enter hhmmss hh = hours, mm = minutes, ss = seconds (military time)
4. Press hold
5. Enter mmddyyyy where mm = month, dd = day, yyyy = year
6. Press hold
7. Press Speaker

Top of Page

1. Press the "Enter" navigation button to begin feature setup.
2. Press the down arrow until the screen display includes TIME/DATE.
3. Press "Enter". The screen display includes HOUR and the current hour setting
4. Press the right or left arrows until the correct hour displays.
5. Press the down arrow to save the hour setting. The screen display shows "MINUTE" and the current minute setting.
6. Press the right or left arrows until the correct minute is shown.
7. Press the down arrow to save the minute setting. The screen display includes AM/PM and the current setting.
8. Press the right or left arrow to toggle between AM and PM.
9. Press the Down arrow to save the AM/PM setting. The screen display includes MONTH and the number of the current month setting.
10. Press the right or left arrow until the number of the correct month is shown.
11. Press the down arrow to save the month setting. The screen now displays DATE and the current day of the month setting.
12. Press right or left arrows until the correct day of the month is shown.
13. Press the down arrow to save the day of the month setting. The screen now displays DAY OF WEEK and the current setting.
14. Press the right or left arrows until the correct day of the week is shown.
15. Press the down arrow to save all settings. The screen now displays MAIN MENU.
16. Press and hold the "Enter" key to return to the idle screen.

Top of Page

Avaya/Lucent Partner Telephone System

1. At station/ext. # 10, press feature, 0, 0
2. Press the left intercom 2 times
3. Enter # 103
4. Enter the correct time in 24 hr. format, for example:
   • to set the time for 09:00 A.M., enter 0900
   • to set the time for 04:45 P.M., enter 1645
5. Press feature, 0, 0

Top of Page

Comdial Digitech

1. Press the "ITCM" key.
2. Dial *#01.
3. Enter the date in YYMMDD format.
4. Enter 2 digits (00-23) for hour and 2 digits for minutes.
5. Press SPKR to end.

Top of Page

Comdial DSU/DSU II

1. From extension 10, press "*#746*"
2. Option One.
   • Dial "01"
   • Dial 00-99 for year
   • Dial 10-12 for month
   • Dial 1-31 for day
   • Dial 00-23 for hour
   • Dial 00-59 for minute.
3. Option Two
   • Dial 00-23 for hour
   • Dial 00-59 for minute
   • Dial "#" to assign hours and minutes.
4. Press speaker to exit.

Top of Page

Comdial DX-80 System

1. Press Feature # * and enter in your password (Default password ########) 
2. Press Show and enter 0803
3. Press Save then Show
4. The option to change the Year will appear - if you do not need to change the year, press Next - if you need to change this value, press Chg, enter in two digits for the year and press Save then Next
5. The option to change the Month will appear - if you do not need to change the month, press Next - if you need to change this value, press Chg, enter in two digits for the month and press Save then Next
6. The option to change the Day will appear - if you do not need to change the date, press Next - if you need to change this value, press Chg, enter in two digits for the date and press Save then Next
7. The option to change the Weekday will appear - if you do not need to change the weekday, press Next - if you need to change this value, press Chg, to select the weekday, and press Next
8. The option to change the Hour will appear - press Chg and enter in two digits for the hour in military format - press Save then Next
9. The option to change the Minutes will appear - press Chg and enter in two digits for the minutes and press Save
10. Press the Hold button to exit programming mode

Top of Page

Comdial Executech

1. Press ITCM *#.
2. Dial 01
3. Dial two digits (00-99) for year.
4. Dial two digits (01-12) for month.
5. Dial two digits (01-31) for day.
6. Dial two digits (00-23) for hour.
7. Dial two digits (00-59) for minute.
8. Dial one digit (1-7) for day of week. SUN = 1, SAT = 7
9. Press * for next feature or press MNTR (SPKR) to end.

Top of Page

Comdial Impact

1. Without picking up the handset, press "Intercom" and dial "*#01". The display should show "Set Clock".
2. Set the year by dialing 00-99.
3. Set the month by dialing 01-12.
4. Set the day by dialing two digits 01-31.
5. Set the hour by dialing 01-23.
6. Set the minutes by dialing 00-59.
7. Pick up and replace the handset to complete.

Top of Page

Comdial DXP

1. Press "Intercom *#0*".
2. Select "01".
3. Enter date (MM:DD:YY).
4. Enter time (HH:MM).
5. Press "#" to end.

Top of Page

ESNA Telephony Office Linx

1. Go to main menu on ESNA (Telephony Office-Linx window).
2. Choose "System" on the tool bar, then "Commands".
3. Enter current date MM:DD:YYYY.
4. Press "Execute".
5. Choose "Exit".
6. Minimize screen.

Time

1. Go to main menu as above.
2. Choose "System" on the tool bar, then "Commands".
3. Enter current date MM:DD:YYYY.
4. Press "Execute".
5. Choose "Exit".
6. Minimize screen.

Top of Page

Executone CX816

1. From station 100, take the handset off-hook.
2. Dial "*".
3. Dial "7764" (PROG).
4. Press the "FLASH" button.
5. Dial "28".
6. Enter time and date as follows: YYMMDDHHMMSS.
7. Press the "HOLD" button.

Enter time and date in the following formats-
Year (YY) =00-99
Month (MM) =01-12
Day (DD) =0-31
Hour (HH) =00-24
Minute (MM) =00-60
Second (SS) =00-60

1. Press "SPKR" or lift handset. Press "436" to enter voice mail.
2. Press the "#" key, mailbox "5000", press password "5000" (default on most systems, yours may differ) then the "#" key.
3. Press "5" to change time and date.
4. After the current date plays, enter the current date MM:DD:YY.
5. After the time plays, enter the new time HH:MM:SS in military format.
6. When finished, press the "*" key until you hear "exiting the system".

Top of Page

Executone Isoetec IDS via Operator's Phone M-32 Series

1. Lift the Handset.
2. At the dial tone, dial "28" then the 4-digit time in military format. For example, "1500" = 3:00PM.
3. A confirmation tone is heard.

Top of Page

Executone Isoetec IDS via Operator's Terminal

1. While the terminal is idle, press and hold Ctrl and "C". Release both keys. The cursor moves to the Hour field.
2. Enter the 2-digit hour in 24-hour clock format (ie., 16 for 4pm). The cursor moves to the Minutes field.
3. Enter the 2-digit minutes. The cursor moves back to the Hour field.
4. Press the Return key. The cursor moves to the Month field.
5. Enter the 2-digit month, day and year. The system inserts the "-" automatically.
6. Press and hold Ctrl and "C". Release.

Top of Page

Executone Isoetec Medley

1. Press the "Menu" key.
2. Press "Park 3".
3. Enter the password (default is "456")
4. Press "#".
5. Press "1" for System Functions.
6. Press "4" for System Clock.
7. Enter the time in 12-hour format.
8. Press "#"
9. Press AM or PM by pressing "Park 3" in the LCD screen.
10. Press "#" to confirm.
11. Hang up or press "HF".

1. Menu (F1)
2. Park 3 Key
3. Enter the Installer Password. 789 at Default.
4. Press # to confirm
5. Dial 9819
6. Enter the Month
7. Press # to confirm
8. Enter the Day
9. Press # to confirm
10. Enter the Year
11. Press # to confirm

Top of Page

Inter-Tel Axxent

1. While the phone is idle, enter "9800". Display shows "DATE:" 
2. Enter Date MM:DD:YY. Press "#" to skip date entry.
3. The display will show "TIME". Enter the time in 12-hour format.
4. The display will then show: "Press 1 for AM, press 2 for PM". Select one.
5. Press "#" to exit.

Top of Page

Inter-Tel Axxess Networked Systems

1. While on hook, enter the Set Network Date and Time feature code (9810). Your displays the current date.
2. If you do not need to change the date, press "#" or ACCEPT to skip to the time prompt.
3. Use the dialpads to enter month day and year mm-dd-yy format.
4. If you make a mistake, press "MUTE" to backspace or "*" to start over.
5. Use the dialpad buttons to enter the time in hours and minutes "0900" for 9:00.
6. If 12-hour display is used, the display shows AM or PM. Press "1" for AM and "2" for PM.

Top of Page

Inter-Tel Axxess Non-Networked Systems

1. While on-hook, enter "9800" for Set Date/Time feature. The current date will display.
2. Press "#" to skip. To change, use keypad to enter the month, day and year (010305=January 3, 2005). The new date will display. 
3. Use keypad keys to enter the time in hours and minutes (0900=9:00). 
4. If the system is set for 12-hour format, the display will show select AM OR PM (AM=1 PM=2). Select 1 or 2.
5. The display reads, "SYSTEM DATE AND TIME UPDATED".

Top of Page

Inter-Tel GLX-PLUS

1. While on-hook, press "SPCL" and enter the Program Time/Date feature code (4)
2. Enter the Program Time feature code (1). Display will show TIME XX:XX
3. Enter the 2-digit number for hour (00-24) and 2-digit for minutes (00-59).
4. Lift and replace the handset.

1. While on-hook, press "SPCL" and enter the Program Time/Date feature code (4).
2. Enter the Program Date feature code (2). Display will show DATE DAY MON XX
3. Press "*" until the correct day is displayed. Press "#". Repeat for month and date.
4. Lift and replace the handset.

1. While on-hook, press "SPCL" and enter the Program Time/Date feature code (4).
2. Enter the Program Date feature code (3). Display will show YEAR:XXXX.
3. Enter 4 digits for the year (0000-9999).
4. Lift and replace the handset.

Top of Page

Inter-Tel IMX 1224/2460

1. While on-hook, press the "SPCL" key and enter the set time of day feature code (021). Display will show "SET TIME OF DAY".
2. Use the keypad to enter the time in hours and minutes. Then press "*" for AM or "#" for PM. Display will show "SET DATE MM:DD:YYYY".
3. Use the keypad to enter the month, day and year. Backspace to correct mistakes by using the "MUTE" key. Display will show "SET DAY OF WEEK SUN".
4. Select the day of the week by scrolling through the selections. Press "#" to go forward and "*" to go back. When the desired day is displayed, press the "SPKR" key to end.

Top of Page

Inter-Tel Encore CX

1. From the programming extension, press the PROGRAM key.
2. Press the Scroll Down key until "System Programming" is displayed.
3. Select "System Programming".
4. Enter the System Programming password and select "System".
5. Select "Time and Date".
6. Enter the time in 24-hour format (ie. 11:50pm=2350).
7. To change the time only, select "Confirm".
8. To enter the date,enter in mmddyy format.
9. Press the speakerphone key to finish programming.

Top of Page

Norstar Merdian

1. Press Feature.
2. Enter "**8463".
3. Enter the password (default is 266344). The display shows

Hour: 01
Next               Change
4. Select CHANGE. Display shows:

Hour: __
Cancel
5. Enter two digits for the hour. Chose AM or PM when Prompted.
6. Select NEXT.

The display shows:
Minutes: 00
Next              Change
7. Enter the minutes.
8. Press the RLS button to end, or press NEXT to change the date.
   The diplay shows:
   Year: 99
   Next              Change
9. Enter the two-digit year.
10. Select NEXT and repeat to change the month and day.
11. Press the RLS key to save the time and date and exit programming.

Top of Page

Norstar Meridian CICS

1. While on-hook, press "SPCL" and enter the Program Time/Date feature code (4)
2. Enter the Program Time feature code (1). Display will show TIME XX:XX
3. Enter the 2-digit number for hour (00-24) and 2-digit for minutes (00-59).
4. Lift and replace the handset.

1. While on-hook, press "SPCL" and enter the Program Time/Date feature code (4).
2. Enter the Program Date feature code (2). Display will show DATE DAY MON XX
3. Press "*" until the correct day is displayed. Press "#". Repeat for month and date.
4. Lift and replace the handset.

1. While on-hook, press "SPCL" and enter the Program Time/Date feature code (4).
2. Enter the Program Date feature code (3). Display will show YEAR:XXXX.
3. Enter 4 digits for the year (0000-9999).
4. Lift and replace the handset.

Top of Page

NEC UX5000 and Aspire

Telephone part numbers 091xxx/08900xx

To set the time for your UX5000/Aspire system:

1. From the System Administrator's telephone (normally extension 301), press CALL1 and dial 828.
2. Dial two digits for the hour (24 hour)

For example, 13=1:00 PM.

3. Dial two digits for the minutes
   You hear confirmation beeps.
4. Press SPK to hang up.

Top of Page

Telephone part numbers 92xxx

To set the time and date for your i-Series system:

1. From the System Administrator's telephone (normally extension 301), press CALL1 and dial 828.
2. Dial the Time and Date password.
   The password is normally 0000.
   
3. Dial two digits for the year (e.g., 05).
4. Dial two digits for the month (01-12).
5. Dial two digits for the day (01-31).
6. Dial the day of the week (0-6).

0=Sunday, 6=Saturday
7. Dial two digits for the hour (24 hour).

For example, 13=1:00 PM.
8. Dial two digits for the minutes (00-60).

You hear confirmation beeps.
9. Press SPK to hang up.
   

Top of Page

Telephone part numbers 88xxx

To set the time:

1. Lift handset
2. Press ICM.
3. Press PGM#.
   -Your display shows, "DSS,EXT,6,9,8?."
   
4. Dial T.
   -Your display shows, "SET TIME
   HHMMSS."
5. Enter the hour (00-23: 0=12 midnight;
   12=12 noon; 23=11 P.M.)
   HHMMSS."
6. Enter the minutes (00-59).
7. Enter the seconds (00-59).
8. Hang up.

To set the time:

1. Lift handset
2. Press ICM.
3. Press PGM#.
   -Your display shows, "DSS,EXT,6,9,8?."
   3.
   
4. Dial 9.
   -Your display shows, "SET DATE
   MMDDYY."
5. Enter the month (01-12, 01=January;12=December)
6. Enter the day of the month (01-31).
7. Enter the last two digits of the year (00-99).
8. Hang up.

Top of Page

Telephone part numbers 824xx

To set the time and date:

1. From extension 10, press SPK + FTR + CLEAR.
2. Dial four digits for the year (e.g., 2005).
   
3. Dial *.
4. Dial two digits (01-12) for the month
5. Dial (01-31) for the date.
6. Dial *.
7. Dial a single digit (0-6) for the day.
   Sunday = 0, Monday =1
8. Dial *.
9. Dial four digits for the time (24-hour clock).

For example, dial 1305 for 1:05 PM.
10. Dial * and press SPK..

The telephone display shows the new date and time.

Top of Page

1. Press "Feat" "#" "0".
2. At the "CHK PSWD:_ prompt, Enter "0000" (Default Password).
3. From the soft menu, press "SAVE".
4. Select "TIME" and press "SHOW".
5. Press "CHG" and enter the "YEAR" and press "SAVE" then "NEXT".
6. Press "CHG" until the correct month appears, then press "NEXT".
7. Press "CHG" and enter the correct day, press "SAVE" and then "NEXT".
8. Press "CHG" until the correct weekday is selected and then press "NEXT".
9. Press "CHG" and enter the correct hour, press "SAVE" and then "NEXT"
 

1. Press "24"
2. Wait to hear the Auto Attendant Greeting
3. Press "#".
4. Press "#" "0".
5. Enter the password (default is 9#56).
6. Press "4" for "Date & Time".
7. Press "1" to review date.
8. Press 2 to change date and time
9. Enter time in 24 hour (military) format.
10. Enter the date MM:DD:YY

Top of Page

Time Set KX-TDA 50/100/200

1. KEYSTROKES.

(Press these keys on the phone designated for programming)
2. Press PROGRAM, STAR, STAR, 1234.
3. Press  SP-PHONE.
4. Press ENTER (or Auto Dial/Store)
5. Press the button below NEXT on the display.
6. Enter the 2-digit hour
7. Enter the 2-digit minute
8. If needed, set AM or PM
9. Press ENTER on the Navigator Wheel or the button labeled Auto Dial/Store.


Lift handset and hang up to leave programming mode or press exit

Top of Page

Time Set KX-T 308

1. You must be on the main phone, station 11, to set time.
2. Press Intercom.
3. Dial 77
4. Enter the hour (01 through 12)
5. Enter the minute (00 through 59)
6. Dial 0 for AM or 1 for PM
7. Press #
8. Hang up.
   

Top of Page

Time Set KX-T 616

1. You must be on the main phone, station 11, to set time.
2. Press Intercom.
3. Dial 77
4. Enter the hour (01 through 12)
5. Enter the minute (00 through 59)
6. Dial 0 for AM or 1 for PM
7. Press #
8. Hang up.
   

Top of Page

Time Set KX-T 1232

You must be on the main phone on jack 01 to set time. You can determine if your phone is jack 01 by setting the switch on the end of a display phone to PROGRAM and then pushing the number 6 on the dial pad. The phone will read the jack and extension number. When you have determined the jack 01 phone, do the following:

1. Set switch on end of phone to "PROGRAM"
2. Dial "0"
3. Enter year (last 2 digits)
4. Enter month (01-12)
5. Enter day (01-31)
6. Enter day of week: (Sun 0, Mon 1, Tue 2, Wed 3, Thu 4, Fri 5, Sat 6.)
7. Enter Hour (01-12)
8. Enter Minute (00-59)
9. Press 0 for AM 1 for PM
10. Press "AUTO DIAL/STORE" key
11. Return phone switch to "SET"

Top of Page

Time Set KX-TD 308, 816, 1232, 500 and KX-TA 1232

You must be on the main phone on jack 01 to set time. You can determine if your phone is jack 01 by pressing PROGRAM 99 on a display phone and then pushing the number 6 on the dial pad. The phone will read the jack and extension number. When you have determined the jack 01 phone, do the following:

Example is to change time from 3:15 PM to 4:17 PM
KEYSTROKES (Press these keys)

1. Press PROGRAM * * 1234 (Default password is 1234. yours may have been changed)
2. Press SP-PHONE 3 Times
3. Enter 2 digit hour
4. FWD/DND button or press the softkey below -> on the display
5. Enter 2-digit minute
6. Auto Dial/Store Button
7. Lift handset and hang up to leave programming mode

Top of Page

Toshiba DK 280

1. From receptionist station, without lifting the handset, press "Intercom"
2. Dial "#651"
3. Dial the time in YY:MM:DD format.
4. Press "Redial" or "#".
5. Press speaker

1. From receptionist station, without lifting the handset, press "Intercom"
2. Dial "#652"
3. Dial the time in military format HH:MM:SS.
4. Press "Redial" or "#".
5. Press speaker.

1. From receptionist station, without lifting the handset, press "Intercom"
2. Dial "#653"
3. Dial the day of the week (1-7).
4. Press "Redial" or "#".
5. Press speaker.

Top of Page

Toshiba Perception

Follow all steps even if you wish to change only the time on your system.

1. Display Date:
2. Press the "DIS TOD" key.
3. The date is now displayed as follows:

           SRC     cos  DEST
           Month  Day Year

Enter the date on the dial pad in MMDDYY format. The new date is displayed.

1. Display Time:
2. Press the "DIS TOD" key again.
3. The date is now displayed as follows:

           SRC     cos     DEST
           Hours Minutes Seconds

1. Enter the time in military time HHMMSS format (for example, 090105 for 9:01 am and 5 seconds and 210105 for 9:01pm and 5 seconds). The new time is displayed.
2. To Start the Clock and Clear Display:
   Press the "DIS TOD" key a third time.

Top of Page

Vodavi Starplus 616, 1224, 2448, and 96EX

1. Press ON/OFF button
2. Dial 76 on the dial pad
3. Enter time and date as follows: YY MM DD HH MM
   HH= Hour (00-23)
4. Press HOLD.

Top of Page

Vodavi StarPlus-Triad, Digital, Mach I, Infinite, DVX and XTS

1. The first attendant station may set system time and date.
2. Dial [692].
3. Enter time and date in the following format: YY MM DD HH MM.
   HH= Hour (00-23)
4. When the correct number of digits are entered, a confirmation tone sounds.

Top of Page

Vodavi Starplus STS System

To set using the feature code:

1. Dial [692] on the dial pad. A confirmation tone will sound.
2. Enter date and time as follows: YYMMDDHHMM
3. YY = Year (00-99)
4. MM = Month (01-12)
5. DD = Day (01-31)
6. HH = Hour (00-23)
7. MM = Minute (00-59)
8. When the correct number of digits are entered, a confirmation tone will sound.
9. Press the ON/OFF button to OFF to update the display.

Top of Page

Vodavi Infinite

Enter programming mode by dialing **3226 from any 24-button display phone.

1. Press FLASH and dial 11.
2. The display should show:

DATE & TIME
MM/DD/YY      HH:MM am
3. Choose display format by pressing the appropriate button in the flexible button field.
4. Press the HOLD button or dial in the time and date as follows (12 digits): YYMMDDHHMMSS
5. Press HOLD to save. A confirmation tone plays and the display updates.